No results were found for the filter!
To ensure that the clutch discs can withstand the high stresses and temperatures of racing, these pads are made of carbon fibre. Wear and fading are reduced to a minimum and even under extreme loads the material prevents the pads from...
Available
€60.95
*
Cork-based product, impregnated with aluminium particles to increase durability and heat resistance. The material is highly compacted to avoid swelling. The CK series clutch kits contain a complete set of friction linings and are...
Available
€35.95
*
Features Increased compression force of 10 to 15% compared to standard springs Reduction of clutch slippage Made of heat-treated carbon steel
Available
€13.99
*
With the Athena GET Chiptuning, the original performance of the KTM Duke can be increased by a few extra horsepower, depending on which setup is used. The GET unit is simply exchanged for the original CDI control unit. Afterwards the...
Almost gone
€329.95
*
You need a new oil seal kit for tuning your KTM Duke 125cc engine? We offer you the complete set from the manufacturer Athena, consisting of the matching five rings. Athena supplies the seal set exclusively in the best original equipment...
Almost gone
€17.99
*
Newfren offers a wide range of brake spare parts as well as clutch pads in different qualities. The cork pads offered here are well comparable with the original pad plates. But according to Newfren they should last a bit longer than the...
Available
€69.95
*
In addition to the standard cork clutch facings, Newfren can also offer you a reinforced carbon kit. The special carbon mixture makes the clutch plates much more grippy! This makes it impossible for the clutch to slip even with heavily...
Available
€89.95
*
The V-Force reed valve block from Italkit has a maximum cross-section on the smallest valves. This allows the diaphragms to open and close with less inherent gas force, resulting in higher efficiency and improved motor performance....
Available
€109.90
*
This compact flow-through cooler is the perfect addition for water-cooled engines where every degree counts. It is installed directly in the cooling circuit and provides additional heat dissipation - particularly useful for tuned setups...
Available
€16.95
*
This compact flow-through cooler is the perfect addition for water-cooled engines where every degree counts. It is installed directly in the cooling circuit and provides additional heat dissipation - particularly useful for tuned setups...
Available
€16.95
*
Replacement petrol tap for Rieju motorcycles (MRT). Technical data Diameter: 15mm Cock positions : Left side : To Top : Open Right : Reserve Incl. fuel filter. OEM number for comparison : 0/000.370.0500
Available
€12.99
*
Here we offer a vacuum fuel tap for all motorcycle models with carburetor. The fuel tap is simply pushed into the tank instead of the old one and can also be used to convert from manual operation to automatic operation. We recommend to...
Available
€8.99
*
Here we offer a simple choke, with an actuator, which can be installed in the fairing of the vehicle as desired. The lever is delivered with a cable pull, can only be used in vehicles with carburetor.
Available
€12.99
*
6mm clamp for fuel hoses. Delivered is 1 piece.
Available
€1.99
*
As some cylinders are only supplied with one gasket, the adjustment of timing and pinch point is often not easy to achieve. In such a case the real moped tuner always has a sheet of gasket material at hand, from which he can cut an...
Available
€2.49
*
Hose clamps can be used in almost any application. Whether as reinforcement of the rubber mountings of the exhaust, or as a normal water hose clamp.
Available
€1.29
*
Cooling hoses with internal spiral for reinforcement. In contrast to the conventional black hoses, you can use the transparent cooling hoses to determine exactly whether there is still air in the cooling circuit to exclude possible...
Available
€14.99
*
;
From €9.99
*
Fuel hose with one meter length and 5mm inner diameter. In many different colours. In addition to its actual use as a petrol hose, it can also be used as a hose for many other purposes. Available in many different colours. The hose can...
Available
€2.00
*
NEW
Retaining rubber radiator, Outer diameter 23.5 mm x inner diameter 11 mm x height 10 mm
This rubber bushing for the radiator bracket is used for secure and low-vibration mounting of the radiator. It effectively absorbs vibrations and thus protects the radiator from damage. Thanks to the elastic material, it fits perfectly...
Available
€3.99
*
NEW
High-quality protection kit for engine and engine housing, specially developed to protect sensitive components against impacts, stone chips and tough riding conditions. The kit offers additional mechanical protection for the crankcase,...
Almost gone
€57.99
*
NEW
Locking bolt, Screw and seal, various Sizes
The oil drain plug is a small but important spare part - it ensures that your engine oil remains safely in the engine housing and can be drained cleanly when changing the oil. If the thread is damaged or the old screw is twisted, this...
Out of Stock
€4.99
*
NEW
Manual choke cable Motoforce, PWK / CP / Flat Slide carburetor, red
The manual choke for PWK and Polini CP carburetors gives you full control over the cold start of your scooter or moped. Instead of relying on an automatic choke, you can now adjust the fuel/air mixture manually. This ensures reliable...
Almost gone
€6.90
*
NEW
Retaining rubber radiator, 19x9,7x3x8, various colors Colors
Whether your radiator rattles or simply no longer sits properly - you can quickly remedy the situation with the right retaining rubber. This fastening element made of high-quality silicone is specially designed and ensures a secure,...
Available
€3.99
*
NEW
Retaining rubber radiator, 24,5x12,5x14x3mm, various colors Colors
If the radiator wobbles, rattles or is no longer secure, it's time for a fresh hold. This retaining rubber is exactly the right spare part for many models - and ensures that your radiator is securely mounted again without vibration. The...
Available
€4.99
*
Du bist der stolze Besitzer eines 125er Motorrads und möchtest dein Bike auf Vordermann bringen? Dann bist du bei uns genau richtig! Als Experten für Motor-Ersatz- und Tuningteile bieten wir alles, was du für eine Optimierung deines Bikes brauchst.
Von neuen Zylinderkits und Kurbelwellen über hochwertige Auspuffanlagen, diverse Filter und Dichtungen bis hin zu Abdeckungen und Schrauben – bei uns findest du alles, was dein 125er Motorrad zu einem echten Unikat macht. Und das Beste daran: Unsere Produkte sind nicht nur von bester Qualität, sondern auch noch zu erschwinglichen Preisen zu bekommen.
Egal, ob du ein erfahrener Tuner bist oder gerade erst damit beginnst, dein Bike aufzumotzen: Mit unserem breiten Angebot an Motor-Ersatz- und Tuningteilen bist du für jede Situation gerüstet. Also worauf wartest du noch? Schau jetzt bei uns vorbei und mache dein 125er Motorrad zu deinem ganz persönlichen Traumbike!
Viewed