1. Choose model
Duke 125 (ab 2024, IS DK A (Euro 5+))
Duke 125 (2021 bis 2023, IS DUKE - Euro5)
Duke 125 (2017 bis 2020, IS DUKE - Euro4)
Duke 125 (2011 bis 2016, Euro3)
2. Filter by category
No results were found for the filter!
Copper seal ring. Technical data Inner diameter: 31.50 mm Outside diameter: 40.00 mm thickness: 4 .00 mm
Almost gone
€5.95
*
Replacement graphite manifold gasket. Fits in principle all vehicles with straight flange or plug-in flange connections up to 42mm diameter. (42mm is for example the original size of the Yamaha YI-3 & YI-4 engine).
Available
€4.99
*
Aluminium/steel manifold gasket from Athena. Can be used on all vehicles with the corresponding outlet dimension of 45mm diameter.
Almost gone
€4.50
*
Maintenance work on the engine is always a good opportunity to replace the seals at the same time. If maintenance work is necessary on the alternator side of the engine, we recommend to install a new gasket, if the cover is already removed.
Available
€8.99
*
If the coupling is replaced or other maintenance work is pending under the coupling cover, it is always advisable to invest in a new seal at the same time. Subsequent oil leaks are always annoying and can thus be avoided.
Available
€7.99
*
Complete engine gasket set from Athena, suitable for KTM 125cc 200cc and 390cc 4-T engines. The gasket set includes cylinder base, head & valve cover gaskets as well as the gaskets for clutch & alternator covers and many other small...
Available
€76.95
*
Fuel tap, universal, M16 x 1,5
Largely universal, vacuum-controlled petrol tap with screw connection. The scope of delivery also includes the pre-filter (tube), which sits in the petrol tap. Suitable for all petrol tanks with corresponding thread & vacuum connection....
Available
€10.99
*
Graphite sealing ring from Athena. Can be used in many different vehicles as a seal for overlapping plug connections.
Available
€13.95
*
Hose clamp assortment, 50 parts
Galvanized steel hose clamps with worm thread for attaching hoses to pipes and hose nozzles. Including 8mm socket wrench. Sizes: 12 x 13-19mm 12 x 16-22mm 10 x 18-27mm 7 x 20-32mm 5 x 22-38mm 3 x 24-44mm
Available
€27.95
*
18mm hose clamp from Piaggio, can of course be used on all vehicles. OEM part number for comparison purposes 879888; 256074; 577557; AP8104072
Available
€4.99
*
Available
€1.99
*
Handmade radiator with 20% more cooling capacity suitable for KTM 125 Duke & 390. With this cooler, different material thicknesses are used. In places subject to particularly high stress, such as brackets, the material is stronger and...
Available
€199.90
*
Available
€1.49
*
Timing chain tensioner seal Flat gasket KTM- Original spare part OEM part number for comparison purposes 90136003003
Almost gone
€3.50
*
Seal timing chain tensioner KTM, KTM Duke, RC 125/200/390, O-ring
Timing chain tensioner seal O-ring 10.15X1.5 mm Original spare part OEM part number for comparison purposes J770010015
Available
€2.19
*
With the Athena GET Chiptuning, the original performance of the KTM Duke can be increased by a few extra horsepower, depending on which setup is used. The GET unit is simply exchanged for the original CDI control unit. Afterwards the...
Almost gone
€329.95
*
You need a new oil seal kit for tuning your KTM Duke 125cc engine? We offer you the complete set from the manufacturer Athena, consisting of the matching five rings. Athena supplies the seal set exclusively in the best original equipment...
Almost gone
€17.99
*
Oil hose, universal
In the course of time the original hose can become porous, so that oil leaks out. This will not only make your engine dirty, but it will also lose lubrication, which can lead to the dreaded piston jam. 1m - universally applicable. 3 x 5mm
Available
€2.99
*
Petrol tap, universal
Manual fuel tap. Especially useful for converted carburettors or intake manifolds which are not equipped with a vacuum connection. Usually the vacuum taps are then drilled through. In order to prevent the unintentional leakage of petrol...
Almost gone
€8.49
*
Spring clip for fuel line
Spring clip for a tight fit of the fuel hose on the fuel tap and carburetor connection. 8,8 - 9,5mm
Available
€2.99
*
If you don't want to change the thermometer in the cylinder head, or the thread doesn't fit, we can offer you this nice anodized adapter which is simply put between the cooling hose. Fits in combination with Stage6 Multimeter & Koso PRO...
Available
€28.95
*
Viewed