1. Choose model
RX/SX 125 (ab 2025, XS)
RX/SX 125 (2021 bis 2024, KT - Euro5)
SX 125 (2018 bis 2020, KXB - Euro4)
SX 125 (2008 bis 2014)
2. Filter by category
No results were found for the filter!
Spacers for handlebar clamps - So that you can also use them with a different handlebar thickness. For example, if you have 22mm handlebars but 28mm clamps , you can still use them together.
Available
€3.99
*
This intermediate tensioner is a practical accessory for adjustments or simply to adjust the tension of a Bowden cable. With a spring travel of 18 mm, it enables precise adjustment of the cable tension.
Available
€0.99
*
Available
€2.99
*
Simple exhaust spring, to hang the exhaust system on the cylinder, or to connect the muffler & manifold. Can also be used for other tinkering. The spring has ring eyelets at both ends. A little trickier to fit, but the hold is better!...
Available
€2.59
*
Typical brake disks, or sprocket bolt with blue dry thread lock (medium strength). Can also be used anywhere else on the moped. Thread: M6 Head: Flat / Torx Length: 20 mm
Available
€1.99
*
During maintenance work on the brake system, these small parts are often lost. The bleeder nipple can then become clogged and maintenance of the brake system becomes impossible the next time. A cover should therefore always be installed!
Available
€2.99
*
Almost universally applicable adjusting screw for clutch cables. Thread: M6 Inner diameter: 8,5 mm
Available
€2.49
*
Wheel bearing which can be used for different vehicles as front or rear wheel bearing. Note Please compare the technical data of this bearing with your original wheel bearing. Technical data Outside diameter: 32 mm width: 10 mm Inner...
Available
€5.99
*
Universal SKF bearing of type "6202-2RS", sealed on both sides. Suitable for example as rear or front axle bearing. But please compare your bearing type before ordering! Technical data Type : 6202 Inner diameter : 15 mm Outside diameter...
Available
€5.99
*
Magnetic oil drain plugs collect the metallic abrasion at the magnet and thus protect the engine & gearbox from excessive wear. Supplied with sealing ring.
Available
€5.99
*
Nut with M7 thread for fixing the cylinder head. A set of 4 special nuts is supplied. The nuts have a length of 13mm and have a collar. Special thread M7. Suitable for all Minarelli, Kymco, MBK, Yamaha, CPI, Keeway engines and other...
Out of Stock
€3.99
*
6mm clamp for fuel hoses. Delivered is 1 piece.
Available
€1.99
*
We can supply these spare clips for your fairing at a reasonable price. 10 pieces - For M6 screws!
Available
€8.99
*
Here we can offer you 10 sheet metal nuts incl. the suitable lens head cross recessed screws. The screws and lenses are especially suitable for fixing the fairing. The brass-coloured screws also give your moped a noble gold screw look....
Available
€5.19
*
Hose clamps can be used in almost any application. Whether as reinforcement of the rubber mountings of the exhaust, or as a normal water hose clamp.
Available
€1.29
*
Motorcycle mirrors as well as the manufacturer's built-in mount on the handlebars are unfortunately not always the same. So it is sometimes necessary to get suitable adapters for the mirror to be able to screw the mirror onto the moped....
Available
From €3.59
*
NEW
Der Movetronix Flare V5 Stunt Firescraper ist das perfekte Upgrade für deine Supermoto, wenn du bei Stunt-Sessions für spektakuläre Effekte sorgen willst. Unter dem Heck montiert, erzeugt der spezielle Firestone-Block beim Kontakt mit...
Almost gone
€23.95
*
NEW
Bei diesem Artikel handelt es sich um ein Originalersatzteil (OEM) der Firma Aprilia OEM Artikelnummer zu Vergleichszwecken : 2R000357 Lieferumfang: 1
Out of Stock
€1.99
*
NEW
Bei diesem Artikel handelt es sich um ein Originalersatzteil (OEM) der Firma Aprilia OEM Artikelnummer zu Vergleichszwecken : AP8104597 Lieferumfang: 1
Out of Stock
€11.99
*
NEW
Die Spiegel Gewinde Abdeckschrauben M10 x 1,25 dienen zur sauberen und sicheren Abdeckung der originalen Spiegelgewinde am Lenker, insbesondere bei der Verwendung von Lenkerendenspiegeln. Gefertigt aus hochwertigem CNC-gefrästem...
Almost gone
€10.99
*
NEW
Auspuffschelle, universell, 40-43mm, Edelstahl
Diese hochwertige Gelenkbolzenschelle eignet sich für Auspuffanlagen mit einem Durchmesser von 40 bis 43 mm. Durch die umklappbare Brückenkonstruktion lässt sich die Schelle direkt um Schlauch oder Rohr legen, ohne dass diese demontiert...
Available
€5.99
*
NEW
This item is an original replacement part (OEM) from Aprilia OEM part number for comparison purposes : 1A009076 Scope of delivery: 1
Almost gone
€15.99
*
NEW
Bei diesem Artikel handelt es sich um ein Originalersatzteil (OEM) der Firma Aprilia OEM Artikelnummer zu Vergleichszwecken : 00H00202101 Lieferumfang: 1
Available
€3.99
*
NEW
This item is an original replacement part (OEM) from Aprilia OEM part number for comparison purposes : 00H00201111 Scope of delivery: 1
Almost gone
€15.99
*
Viewed